-
金牌商家
我的认证 您的信赖
上海甲克自动化科技有限公司
-
- 陈
- 好评率：100%
动态评价
描述相符：5.05.0分
服务态度：5.05.0分
发货速度：4.94.9分
物流速度：4.94.9分
店铺信息
认证信息：
保证金：10000.00
商品数量：3169
创店时间：2016-03-14
店内搜索
分类
- 品牌：AB
Technical Specifications
Mechanical
| Degree of protection (IP) | IP20 |
| Shock | 15 G peak for 11 ms duration (±1.0 ms) |
| PWM frequency | 4 kHz @ 540V DC |
| Vibration | 0.152 mm (0.006 inch) displacement, 1 G peak |
Electrical
| Number of analogue outputs | 2 |
| Mains voltage | 400 V |
| Integrated breaking resistance | No |
| Brake IGBT | Brake IGBT installed |
| Internal communication module | No communication module |
| Fuse current rating | 6 A @ 540V DC |
| Input voltage rating | 400V AC, 3-phase, 50 Hz |
| AC input undervoltage trip | 233V AC @ 380/400V |
| Bus voltage, nom | 540V DC @ 380/400V |
| Bus undervoltage shutoff/fault | 305V DC @ 380/400V |
| Bus overvoltage trip | 810V DC @ 380/400V |
| Output voltage rating | 0...400V AC @ 380...400V AC, 1-phase |
| Circuit breaker current rating, max | 15 A @ 400V AC, 3-phase |
| Motor circuit protector current rating, max | 3 A @ 400V AC, 3-phase |
| Output current rating, continuous | 2.1 A @ 540V DC |
| Output current rating, 1 min | 2.4 A @ 540V DC |
| Output current rating, 3 sec | 3.2 A @ 540V DC |
| Logic control ride-thru | 0.5 seconds minimum, 2 seconds typical |
| Brake resistor | No internal brake resistor |
| Input current rating | 2.1 A @ 540V DC |
| Documentation | Manual |
| Carrier frequency | 2, 4, 8, and 10 kHz. Drive rating based on 4 kHz |
| Encoder quadrature | 90 degrees, ±27 degrees at 25 °C (77 °F) |
| AC input overvoltage trip | 570V AC @ 380/400V |
| Input power rating | 1.3 kVA @ 400V AC, 3-phase |
| Dual element time delay fuse current rating | 3...6 A @ 400V AC, 3-phase |
| Non-time delay fuse current rating | 3...8 A @ 400V AC, 3-phase |
| Digital input latency, typical | 9.2 ms @ stop signal for SVC motor control |
| Heat sink thermistor | Monitored by microprocessor overtemp trip |
| Digital input latency | 9.2...16.0 ms @ start signal for SVC motor control |
| Drive to motor power ratio, max | Recommended not greater than 2:1 ratio |
| Stop modes | Multiple programmable stop modes including — Ramp, Coast, DC-brake, Fast brake, Ramp-to-hold and S-curve |
| Frequency accuracy | Digital input: within ±0.01% of set output frequency |
| Acceleration/deceleration | Two independently programmable accel and decel times. Each time can be programmed from 0...3600 seconds in 0.1 second increments |
| Analog input latency, typical | 6.4 ms @ speed signal for SVC motor control |
| Number of digital inputs | 6 |
| Number of digital outputs | 3 |
| Number of analogue inputs | 2 |
| Internal watts loss | 44 W @ 400V, 0.75 Hp normal duty (IP20, NEMA/UL Type 1) |
| Motor voltage, nom | 400V @ 380...480V drive rating, 400V nominal line voltage |
| Supporting protocol for DeviceNet | Yes |
| Human interface model | No HIM (blank plate inserted) |
| Max. output frequency | 400 Hz |
| External watts loss | 19 W @ 400V, 0.75 Hp normal duty (IP20, NEMA/UL Type 1) |
| Total watts loss | 63 W @ 400V, 0.75 Hp normal duty (IP20, NEMA/UL Type 1) |
| Supporting protocol for EtherNet/IP | Yes |
| Line voltage, nom | 400V @ 380...480V drive rating, 400V nominal motor voltage |
| Mains frequency | 50 Hz |
| Output frequency range | Standard control: 0...400 Hz, vector control: 0...420 Hz |
| Actual short circuit rating | Determined by AIC rating of installed fuse/circuit breaker |
| Internal EMC filtering | With EMC filter with common mode choke |
| Custom drive/firmware | No custom firmware |
| Feedback option | No feedback |
| Analog input latency | 4.8...12.4 ms @ speed signal for SVC motor control |
| Drive full power range | 400...528V @ 380...480V drive rating |
| Drive operating range | 342...528V @ 380...480V drive rating |
| Torque regulation | Without feedback: ±5 %, 600 rad/sec bandwidth |
| Enclosure type | IP20/NEMA/UL Type 1 |
| Output current rating | 2.1 amps, 0.75 kW normal duty, 0.55 kW heavy duty, frame 0 |
| Control options | Standard control with 24V AC/DC I/O |
| Drive overcurrent trip | Instantaneous current limit: 220...300% of rated current (dependent on drive rating) |
| Efficiency | 97.5% at rated amps, nominal line volts |
| Encoder supply | 12V, 250 mA. 12V, 10 mA minimum inputs isolated with differential transmitter, 250 kHz maximum |
| Speed control-speed regulation | Without feedback (Vector Control Mode): 0.1 % of base speed across 120:1 speed range, 120:1 operating range, 50 rad/sec bandwidth |
| Current limit capability | Proactive current limit programmable from 20...160% of rated output current, Independently programmable proportional and integral gain |
| Selectable motor control | Sensorless vector with full tuning. Standards V/Hz with full custom capability and vector control |
| Frequency control-speed regulation | With slip compensation (Volts per Hertz mode): 0.5% of base speed across 40:1 speed range, 40:1 operating range, 10 rad/sec bandwidth |
| Input phases | 3-phase input provides full rating for all drives. 1-phase operation possible on certain drives and provides 50 % of rated current. Frames 0...6: drive can be supplied as 6 pulse or 18 pulse in an engineered package. |
| Control method | Sine coded PWM with programmable carrier frequency, ratings apply to all drives, the drive can be supplied as 6 pulse or 18 pulse in an engineered solution |
| Encoder requirements | Encoders must be line driver type, quadrature (dual channel) or pulse (single channel), 8...15V DC output (4...6V DC when jumpers are in 5V position), single-ended or differential and capable of supplying a min. of 10 mA per channel, maximum input frequen |
| Number of phases output | 3 |
| Number of phases input | 3 |
| Relative symmetric net voltage tolerance | 10 % |
| With control element | Yes |
| Supporting protocol for LON | Yes |
| Supporting protocol for TCP/IP | Yes |
| Supporting protocol for PROFIBUS | Yes |
| Supporting protocol for CAN | Yes |
| Supporting protocol for Modbus | Yes |
| Motor overload protection | Frames 0...6 standard control: powerflex 700 drives with standard control, which is identified by an N, A, or B in position 15 of the catalog number, only provide Class 10 motor overload protection according to NEC article 430, they do not provide speed |
| Input frequency tolerance | 47 Hz |
| Encoder duty cycle | 50% ±10% |
| Displacement power factor (all drives) | 0.98 across speed range |
| Short circuit rating, max | 200000 amps symmetrical |
| Output voltage range | 0 to rated motor voltage |
| Encoder type | Incremental, dual channel |
| Power ride-thru | 15 milliseconds at full load |
| Short circuit trip | Phase-to-phase on drive output |
| Ground fault trip | Phase-to-ground on drive output |
| Drive to motor power ratio, min | Recommended not less than 1:2 ratio |
| Control logic noise immunity | Showering arc transients upto 1500V peak |
| Line transients | Up to 6000 volts peak per IEEE C62.41-1991 |
| Intermittent overload | 110% overload capability for up to 1 minute, 150% overload capability for up to 3 seconds |
Construction
| Height, approx | IP20, NEMA/UL type 1: 336 mm |
| Depth, approx | IP20, NEMA/UL type 1: 200 mm |
| Width, approx | IP20, NEMA/UL type 1: 110 mm |
| Weight, approx | IP20, NEMA/UL type 1: 8.16 kg (drive and packaging weight) |
Environmental
| Sound level | Frame 0: 58 dB @ 30 CFM fan velocity |
| Altitude | 1000 m (3300 ft.) maximum without derating |
| Degree of protection (NEMA) | 1 |
| Surrounding air temperature | IP20, NEMA/UL type 1 (with top label): 0...50 °C (0...122 °F) @ frames 5…6, most ratings |
| Atmosphere | Drive must not be installed in an area where the ambient atmosphere contains volatile or corrosive gas, vapors or dust, If the drive is not going to be installed immediately, store the drive where it is not exposed to a corrosive atmosphere |
| Operating temperature | 50 °C @ 540V DC |
| Storage temperature | -40 °C |
| Relative humidity | 5...95% noncondensing |
| Pollution degree 1 according to EN 61800-5-1 | No pollution occurs, only dry non-conductive pollution occurs, and has no influence |
| Pollution degree 4 according to EN 61800-5-1 | The pollution generates persistent conductivity caused, for example, by conductive dust, rain or snow |
| Pollution degree 3 according to EN 61800-5-1 | Conductive pollution occurs, dry non-conductive pollution occurs and becomes conductive due to condensation |
| Pollution degree 2 according to EN 61800-5-1 | Normally only non-conductive pollution occurs, Occasionally a temporary conductivity, caused by condensation is expected when the drive is out of operation |
| Surrounding environment pollution degree | All enclosures are acceptable for pollution degree 1 and 2, an enclosure that meets or exceeds IP54, NEMA/UL Type 12, is required for pollution degree 3 and 4 |
